How much does cabinet refacing cost in Seattle, WA?

Most Seattle homeowners spend between $3,200 – $11,300 on cabinet refacing, with an average around $7,250. Local labor prices 28% above the national average, so Seattle quotes tend to land at the higher end of national ranges.

Why is cabinet refacing more or less expensive in Seattle than elsewhere?

Seattle trade labor is among the most expensive in the country and books months ahead. Persistent rain demands drainage detailing, flashing and rot-resistant materials.

Do I need a permit for cabinet refacing in Seattle, Washington?

SDCI permits and inspections are required for most exterior and structural work. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Seattle?

Get at least three written quotes from licensed, insured Washington contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Seattle market.

How much does cabinet refacing cost in 2026?

Most homeowners pay between $2,500 and $8,800, with a national average near $5,650. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per linear foot?

Installed pricing usually runs $100.00 to $350.00 per linear foot, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-linear foot price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Cabinet Refacing/Seattle, WA

Seattle · Washington

Cabinet Refacing cost in Seattle, WA

Seattle homeowners typically pay $3,200 – $11,300 for cabinet refacing. Local labor and materials price 28% above the national average.

Get my Seattle estimate Use the Seattle calculator

Seattle average

$7,250

Typical low

$3,200

Typical high

$11,300

Per linear foot

$130 – $450

Sample ZIP

98101

What drives Seattle pricing

Local labor

Seattle trade labor is among the most expensive in the country and books months ahead.

Permits & code

SDCI permits and inspections are required for most exterior and structural work.

Climate & conditions

Persistent rain demands drainage detailing, flashing and rot-resistant materials.

Instant cost calculator

Adjust the inputs to see live pricing

Cabinet run (linear feet)25 linear feet

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$4,275 – $5,819

Most homeowners pay around $5,047

Compare quality / material level

Cost by material in Seattle

Installed Seattle pricing per linear foot.

Option	Installed cost	Pros	Cons
Rigid thermofoil	$180 – $245	—	—
Wood veneer	$245 – $325	—	—
Solid wood doors	$325 – $420	—	—
Custom paint-grade solid wood	$420 – $575	—	—

Where the money goes in Seattle

A typical $7,250 Seattle project, broken down by line item.

Labor0.45% · $33
Materials0.38% · $28
Permits & inspections0.05% · $4
Overhead & profit0.12% · $9

Common add-ons

Extras that show up on Seattle quotes but rarely in the headline price.

New hardware

$130 – $770

Soft-close hinges and slides

$255 – $1,150

Pull-out shelving

$190 – $640

Crown molding

$385 – $1,550

Ways to save in Seattle

Reface only the uppers and paint the lowers for a two-tone look.
Reuse existing hardware if the hole spacing matches.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Seattle FAQs

Get a Seattle price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your WA ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Seattle research

Best cabinet refacing companies in Seattle Cabinet Refacing permits in Washington Cabinet Refacing near me All Washington prices

Cabinet Refacing cost near Seattle

Cabinet Refacing cost in Bellevue, WA

$3,300 – $11,653

Cabinet Refacing cost in Tacoma, WA

$2,875 – $10,152

Cabinet Refacing cost in Everett, WA

$2,950 – $10,417

Cabinet Refacing cost in Kent, WA

$2,975 – $10,505

Cabinet Refacing cost in Renton, WA

$3,000 – $10,594

More Washington cities

Spokane Vancouver Olympia

Other project costs in Seattle

Fence Installation in Seattle

$1,920 – $5,120

Roof Replacement in Seattle

$10,880 – $43,520

Kitchen Remodel in Seattle

$23,040 – $121,600

HVAC Replacement in Seattle

$7,040 – $23,040

Deck Building in Seattle

$5,632 – $15,360

Window Replacement in Seattle

$576 – $1,920

See every Seattle cost guide