How much does chimney repair cost in St. George, UT?

Most St. George homeowners spend between $470 – $3,650 on chimney repair, with an average around $2,050. Local labor prices 4% above the national average, so St. George quotes tend to land at the higher end of national ranges.

Why is chimney repair more or less expensive in St. George than elsewhere?

Licensed trade labor in St. George runs about 104% of the national average, and the best crews book out fastest in spring and early summer. Utah weather drives material choices here, so ask contractors what they install most often in St. George and why.

Do I need a permit for chimney repair in St. George, Utah?

Most St. George, UT projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in St. George?

Get at least three written quotes from licensed, insured Utah contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the St. George metro market.

How much does chimney repair cost in 2026?

Most homeowners pay between $450 and $3,500, with a national average near $1,975. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per job?

Installed pricing usually runs $450.00 to $3,500.00 per job, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-job price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Chimney Repair/St. George, UT

St. George metro · Utah

Chimney Repair cost in St. George, UT

St. George homeowners typically pay $470 – $3,650 for chimney repair. Local labor and materials price 4% above the national average.

Get my St. George estimate Use the St. George calculator

St. George average

$2,050

Typical low

$470

Typical high

$3,650

Per job

$470 – $3,650

Sample ZIP

What drives St. George pricing

Local labor

Licensed trade labor in St. George runs about 104% of the national average, and the best crews book out fastest in spring and early summer.

Permits & code

Most St. George, UT projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not.

Climate & conditions

Utah weather drives material choices here, so ask contractors what they install most often in St. George and why.

Instant cost calculator

Adjust the inputs to see live pricing

Repair scope (jobs)1 job

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$1,188 – $1,663

Most homeowners pay around $1,425

Compare quality / material level

Cost by material in St. George

Installed St. George pricing per job.

Option	Installed cost	Pros	Cons
Sweep and minor sealing	$1,250 – $1,750	—	—
Crown repair and waterproofing	$1,750 – $2,300	—	—
Partial rebuild and tuckpointing	$2,300 – $3,000	—	—
Full rebuild with new liner	$3,000 – $4,100	—	—

Where the money goes in St. George

A typical $2,050 St. George project, broken down by line item.

Labor0.45% · $9
Materials0.38% · $8
Permits & inspections0.05% · $1
Overhead & profit0.12% · $2

Common add-ons

Extras that show up on St. George quotes but rarely in the headline price.

Stainless steel liner

$1,550 – $5,200

Chimney cap

$155 – $625

Flashing replacement

$310 – $1,550

Waterproof sealant

$310 – $935

Ways to save in St. George

Have the sweep and inspection done together in late summer.
Waterproof the crown early — it prevents most rebuild-level damage.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

St. George FAQs

Get a St. George price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your UT ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More St. George research

Best chimney repair companies in St. George Chimney Repair permits in Utah Chimney Repair near me All Utah prices

More Utah cities

Salt Lake City Provo West Valley City Ogden Lehi

Other project costs in St. George

Fence Installation in St. George

$1,560 – $4,160

Roof Replacement in St. George

$8,840 – $35,360

Kitchen Remodel in St. George

$18,720 – $98,800

HVAC Replacement in St. George

$5,720 – $18,720

Deck Building in St. George

$4,576 – $12,480

Window Replacement in St. George

$468 – $1,560

See every St. George cost guide