How much does sump pump installation cost in Billings, MT?

Most Billings homeowners spend between $610 – $2,550 on sump pump installation, with an average around $1,600. Local labor prices 2% above the national average, so Billings quotes tend to land at the higher end of national ranges.

Why is sump pump installation more or less expensive in Billings than elsewhere?

Licensed trade labor in Billings runs about 102% of the national average, and the best crews book out fastest in spring and early summer. Montana weather drives material choices here, so ask contractors what they install most often in Billings and why.

Do I need a permit for sump pump installation in Billings, Montana?

Most Billings, MT projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Billings?

Get at least three written quotes from licensed, insured Montana contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Billings metro market.

How much does sump pump installation cost in 2026?

Most homeowners pay between $600 and $2,500, with a national average near $1,550. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per unit?

Installed pricing usually runs $600.00 to $2,500.00 per unit, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-unit price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Sump Pump Installation/Billings, MT

Billings metro · Montana

Sump Pump Installation cost in Billings, MT

Billings homeowners typically pay $610 – $2,550 for sump pump installation. Local labor and materials price 2% above the national average.

Get my Billings estimate Use the Billings calculator

Billings average

$1,600

Typical low

$610

Typical high

$2,550

Per unit

$610 – $2,550

Sample ZIP

What drives Billings pricing

Local labor

Licensed trade labor in Billings runs about 102% of the national average, and the best crews book out fastest in spring and early summer.

Permits & code

Most Billings, MT projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not.

Climate & conditions

Montana weather drives material choices here, so ask contractors what they install most often in Billings and why.

Instant cost calculator

Adjust the inputs to see live pricing

Number of pumps1 unit

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$931 – $1,283

Most homeowners pay around $1,107

Compare quality / material level

Cost by material in Billings

Installed Billings pricing per unit.

Option	Installed cost	Pros	Cons
1/3 HP pedestal	$980 – $1,350	—	—
1/2 HP submersible	$1,350 – $1,750	—	—
Submersible with battery backup	$1,750 – $2,300	—	—
Dual pump with water-powered backup	$2,300 – $3,150	—	—

Where the money goes in Billings

A typical $1,600 Billings project, broken down by line item.

Labor0.45% · $7
Materials0.38% · $6
Permits & inspections0.05% · $1
Overhead & profit0.12% · $2

Common add-ons

Extras that show up on Billings quotes but rarely in the headline price.

Battery backup system

$410 – $1,200

New sump pit excavation

$510 – $1,850

Discharge line extension

$155 – $610

Interior drain tile

$3,050 – $10,200

Ways to save in Billings

Install backup power — most failures happen during storm outages.
Replace preventively at year 8 instead of after a flood.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Billings FAQs

Get a Billings price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your MT ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Billings research

Best sump pump installation companies in Billings Sump Pump Installation permits in Montana Sump Pump Installation near me All Montana prices

More Montana cities

Missoula Bozeman Great Falls

Other project costs in Billings

Fence Installation in Billings

$1,530 – $4,080

Roof Replacement in Billings

$8,670 – $34,680

Kitchen Remodel in Billings

$18,360 – $96,900

HVAC Replacement in Billings

$5,610 – $18,360

Deck Building in Billings

$4,488 – $12,240

Window Replacement in Billings

$459 – $1,530

See every Billings cost guide