How much does cabinet refacing cost in Albuquerque, NM?

Most Albuquerque homeowners spend between $2,350 – $8,250 on cabinet refacing, with an average around $5,300. Local labor prices 6% below the national average, so Albuquerque quotes tend to land at the lower end of national ranges.

Why is cabinet refacing more or less expensive in Albuquerque than elsewhere?

Licensed trade labor in Albuquerque runs about 94% of the national average, and the best crews book out fastest in spring and early summer. New Mexico weather drives material choices here, so ask contractors what they install most often in Albuquerque and why.

Do I need a permit for cabinet refacing in Albuquerque, New Mexico?

Most Albuquerque, NM projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Albuquerque?

Get at least three written quotes from licensed, insured New Mexico contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Albuquerque metro market.

How much does cabinet refacing cost in 2026?

Most homeowners pay between $2,500 and $8,800, with a national average near $5,650. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per linear foot?

Installed pricing usually runs $100.00 to $350.00 per linear foot, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-linear foot price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Cabinet Refacing/Albuquerque, NM

Albuquerque metro · New Mexico

Cabinet Refacing cost in Albuquerque, NM

Albuquerque homeowners typically pay $2,350 – $8,250 for cabinet refacing. Local labor and materials price 6% below the national average.

Get my Albuquerque estimate Use the Albuquerque calculator

Albuquerque average

$5,300

Typical low

$2,350

Typical high

$8,250

Per linear foot

$94 – $330

Sample ZIP

What drives Albuquerque pricing

Local labor

Licensed trade labor in Albuquerque runs about 94% of the national average, and the best crews book out fastest in spring and early summer.

Permits & code

Most Albuquerque, NM projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not.

Climate & conditions

New Mexico weather drives material choices here, so ask contractors what they install most often in Albuquerque and why.

Instant cost calculator

Adjust the inputs to see live pricing

Cabinet run (linear feet)25 linear feet

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$3,088 – $4,275

Most homeowners pay around $3,681

Compare quality / material level

Cost by material in Albuquerque

Installed Albuquerque pricing per linear foot.

Option	Installed cost	Pros	Cons
Rigid thermofoil	$130 – $180	—	—
Wood veneer	$180 – $235	—	—
Solid wood doors	$235 – $305	—	—
Custom paint-grade solid wood	$305 – $425	—	—

Where the money goes in Albuquerque

A typical $5,300 Albuquerque project, broken down by line item.

Labor0.45% · $24
Materials0.38% · $20
Permits & inspections0.05% · $3
Overhead & profit0.12% · $6

Common add-ons

Extras that show up on Albuquerque quotes but rarely in the headline price.

New hardware

$94 – $565

Soft-close hinges and slides

$190 – $845

Pull-out shelving

$140 – $470

Crown molding

$280 – $1,150

Ways to save in Albuquerque

Reface only the uppers and paint the lowers for a two-tone look.
Reuse existing hardware if the hole spacing matches.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Albuquerque FAQs

Get a Albuquerque price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your NM ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Albuquerque research

Best cabinet refacing companies in Albuquerque Cabinet Refacing permits in New Mexico Cabinet Refacing near me All New Mexico prices

More New Mexico cities

Santa Fe Las Cruces Rio Rancho

Other project costs in Albuquerque

Fence Installation in Albuquerque

$1,410 – $3,760

Roof Replacement in Albuquerque

$7,990 – $31,960

Kitchen Remodel in Albuquerque

$16,920 – $89,300

HVAC Replacement in Albuquerque

$5,170 – $16,920

Deck Building in Albuquerque

$4,136 – $11,280

Window Replacement in Albuquerque

$423 – $1,410

See every Albuquerque cost guide