How much does cabinet refacing cost in Santa Fe, NM?

Most Santa Fe homeowners spend between $2,550 – $9,000 on cabinet refacing, with an average around $5,750. Local labor prices 2% above the national average, so Santa Fe quotes tend to land at the higher end of national ranges.

Why is cabinet refacing more or less expensive in Santa Fe than elsewhere?

Licensed trade labor in Santa Fe runs about 102% of the national average, and the best crews book out fastest in spring and early summer. New Mexico weather drives material choices here, so ask contractors what they install most often in Santa Fe and why.

Do I need a permit for cabinet refacing in Santa Fe, New Mexico?

Most Santa Fe, NM projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Santa Fe?

Get at least three written quotes from licensed, insured New Mexico contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Santa Fe metro market.

How much does cabinet refacing cost in 2026?

Most homeowners pay between $2,500 and $8,800, with a national average near $5,650. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per linear foot?

Installed pricing usually runs $100.00 to $350.00 per linear foot, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-linear foot price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Cabinet Refacing/Santa Fe, NM

Santa Fe metro · New Mexico

Cabinet Refacing cost in Santa Fe, NM

Santa Fe homeowners typically pay $2,550 – $9,000 for cabinet refacing. Local labor and materials price 2% above the national average.

Get my Santa Fe estimate Use the Santa Fe calculator

Santa Fe average

$5,750

Typical low

$2,550

Typical high

$9,000

Per linear foot

$100 – $355

Sample ZIP

What drives Santa Fe pricing

Local labor

Licensed trade labor in Santa Fe runs about 102% of the national average, and the best crews book out fastest in spring and early summer.

Permits & code

Most Santa Fe, NM projects that change structure, electrical, plumbing or mechanical systems need a permit from the local building department; cosmetic work usually does not.

Climate & conditions

New Mexico weather drives material choices here, so ask contractors what they install most often in Santa Fe and why.

Instant cost calculator

Adjust the inputs to see live pricing

Cabinet run (linear feet)25 linear feet

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$3,325 – $4,631

Most homeowners pay around $3,978

Compare quality / material level

Cost by material in Santa Fe

Installed Santa Fe pricing per linear foot.

Option	Installed cost	Pros	Cons
Rigid thermofoil	$140 – $195	—	—
Wood veneer	$195 – $255	—	—
Solid wood doors	$255 – $335	—	—
Custom paint-grade solid wood	$335 – $460	—	—

Where the money goes in Santa Fe

A typical $5,750 Santa Fe project, broken down by line item.

Labor0.45% · $26
Materials0.38% · $22
Permits & inspections0.05% · $3
Overhead & profit0.12% · $7

Common add-ons

Extras that show up on Santa Fe quotes but rarely in the headline price.

New hardware

$100 – $610

Soft-close hinges and slides

$205 – $920

Pull-out shelving

$155 – $510

Crown molding

$305 – $1,200

Ways to save in Santa Fe

Reface only the uppers and paint the lowers for a two-tone look.
Reuse existing hardware if the hole spacing matches.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Santa Fe FAQs

Get a Santa Fe price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your NM ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Santa Fe research

Best cabinet refacing companies in Santa Fe Cabinet Refacing permits in New Mexico Cabinet Refacing near me All New Mexico prices

More New Mexico cities

Albuquerque Las Cruces Rio Rancho

Other project costs in Santa Fe

Fence Installation in Santa Fe

$1,530 – $4,080

Roof Replacement in Santa Fe

$8,670 – $34,680

Kitchen Remodel in Santa Fe

$18,360 – $96,900

HVAC Replacement in Santa Fe

$5,610 – $18,360

Deck Building in Santa Fe

$4,488 – $12,240

Window Replacement in Santa Fe

$459 – $1,530

See every Santa Fe cost guide