How much does electrical panel upgrade cost in Burbank, CA?

Most Burbank homeowners spend between $2,250 – $5,650 on electrical panel upgrade, with an average around $3,650. Local labor prices 26% above the national average, so Burbank quotes tend to land at the higher end of national ranges.

How many quotes should I get in Burbank?

Get at least three written quotes from licensed, insured California contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Los Angeles market.

How much does a 200 amp panel upgrade cost?

$2,000 to $4,500 typically, or $2,800 to $6,000 if the meter base and service entrance also need replacing.

How long does a panel upgrade take?

One day for the electrical work, with power out four to eight hours. Utility scheduling and inspection may spread it over a few days.

Do I need 200 amps for an EV charger?

Usually. A Level 2 charger draws 40 to 60 amps; most 100 amp services cannot support it without load management.

Is a permit required?

Always. The utility will not reconnect without an inspection sign-off, and unpermitted work surfaces during a home sale.

What are Federal Pacific and Zinsco panels?

Obsolete panels with breakers that fail to trip. Insurers often refuse coverage and replacement is strongly recommended regardless of capacity.

Can I just add a subpanel instead?

A subpanel adds circuit space, not capacity. If your total service is maxed out, you still need the main upgrade.

Home/Cost guides/Electrical Panel Upgrade/Burbank, CA

Los Angeles · California

Electrical Panel Upgrade cost in Burbank, CA

Burbank homeowners typically pay $2,250 – $5,650 for electrical panel upgrade. Local labor and materials price 26% above the national average.

Get my Burbank estimate Use the Burbank calculator

Burbank average

$3,650

Typical low

$2,250

Typical high

$5,650

Per panel

$1,650 – $7,550

Sample ZIP

91502

What drives Burbank pricing

Local labor

Licensed Burbank contractors carry California workers' comp and prevailing wage pressure, and crews here quote roughly 26% above the national labor average. Demand in the Los Angeles market peaks in spring, so booking early usually beats a rush premium.

Permits & code

Burbank follows the California Building Standards Code, so most structural, electrical, plumbing and re-roof work needs a permit from the Burbank building department plus Title 24 energy compliance. Seismic bracing and soft-story retrofit rules apply to many older LA-area properties, and hillside lots trigger extra geotechnical review.

Climate & conditions

Burbank sits in a warm Mediterranean climate with intense summer sun, so expect UV-stable, heat-tolerant materials and shaded scheduling in peak summer.

Instant cost calculator

Adjust the inputs to see live pricing

Panels to upgrade1 panel

Target service size

Service entrance

Panel location

Code corrections

Estimated project cost

$1,650 – $3,150

Most homeowners pay around $2,400

Compare target service size

Cost by material in Burbank

Installed Burbank pricing per panel.

Option	Installed cost	Pros	Cons
100 amp service	$1,650 – $3,150	Fine for small homes with gas heat	No headroom for EV or heat pump
150 amp service	$2,250 – $4,050	Middle ground	Often costs nearly the same as 200
200 amp service	$2,500 – $5,650	The modern standard, supports EV and electrification	May require new meter base
400 amp service	$5,050 – $11,300	Large homes, shops, multiple EVs	Utility coordination and two panels
Subpanel	$755 – $2,500	Cheap way to add circuits	Does not increase total service capacity

Where the money goes in Burbank

A typical $3,650 Burbank project, broken down by line item.

Labor48% · $1,752
Panel and breakers27% · $986
Service entrance materials15% · $548
Permits and inspection10% · $365

Common add-ons

Extras that show up on Burbank quotes but rarely in the headline price.

EV charger circuit

$630 – $2,500

Whole-home surge protector

$315 – $880

Generator interlock or transfer switch

$505 – $3,150

Grounding rod system update

$250 – $1,000

AFCI/GFCI breaker upgrades

Per breaker

$50 – $150

Ways to save in Burbank

Go straight to 200 amp — the incremental cost over 150 is small and you will not repeat the job.
Bundle EV charger, surge protector and any new circuits into the same permit and visit.
Check for utility and federal electrification rebates before you sign.
Get three bids; panel pricing varies more between electricians than almost any other trade.
Ask about keeping the panel in its existing location to avoid relocation cost.

Burbank FAQs

Get a Burbank price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your CA ZIP code — then connect you with vetted local pros.

Get electrician quotes

More Burbank research

Best electrical panel upgrade companies in Burbank Electrical Panel Upgrade permits in California Free electrical panel upgrade quotes in Burbank Affordable electrical panel upgrade in Burbank Emergency electrical panel upgrade in Burbank Electrical Panel Upgrade cost per unit in Burbank Electrical Panel Upgrade near me All California prices

Electrical Panel Upgrade cost near Burbank

Electrical Panel Upgrade cost in Los Angeles, CA

$2,214 – $5,560

Electrical Panel Upgrade cost in Long Beach, CA

$2,179 – $5,471

Electrical Panel Upgrade cost in Pasadena, CA

$2,286 – $5,740

Electrical Panel Upgrade cost in Glendale, CA

$2,232 – $5,605

Electrical Panel Upgrade cost in Santa Clarita, CA

$2,071 – $5,202

Electrical Panel Upgrade cost in Torrance, CA

$2,196 – $5,515

More California cities

San Diego San Jose San Francisco Oakland Sacramento Fresno Anaheim Santa Ana

Other project costs in Burbank

Fence Installation in Burbank

$1,890 – $5,040

Roof Replacement in Burbank

$10,710 – $42,840

Kitchen Remodel in Burbank

$22,680 – $119,700

HVAC Replacement in Burbank

$6,930 – $22,680

Deck Building in Burbank

$5,544 – $15,120

Window Replacement in Burbank

$567 – $1,890

See every Burbank cost guide