How much does sump pump installation cost in Frisco, TX?

Most Frisco homeowners spend between $635 – $2,650 on sump pump installation, with an average around $1,650. Local labor prices 6% above the national average, so Frisco quotes tend to land at the higher end of national ranges.

Why is sump pump installation more or less expensive in Frisco than elsewhere?

Rapid growth keeps Frisco crews booked and prices slightly above metro average. Hail and wind exposure similar to the rest of DFW.

Do I need a permit for sump pump installation in Frisco, Texas?

City permits and HOA review both apply to exterior work. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Frisco?

Get at least three written quotes from licensed, insured Texas contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Dallas-Fort Worth market.

How much does sump pump installation cost in 2026?

Most homeowners pay between $600 and $2,500, with a national average near $1,550. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per unit?

Installed pricing usually runs $600.00 to $2,500.00 per unit, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-unit price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Sump Pump Installation/Frisco, TX

Dallas-Fort Worth · Texas

Sump Pump Installation cost in Frisco, TX

Frisco homeowners typically pay $635 – $2,650 for sump pump installation. Local labor and materials price 6% above the national average.

Get my Frisco estimate Use the Frisco calculator

Frisco average

$1,650

Typical low

$635

Typical high

$2,650

Per unit

$635 – $2,650

Sample ZIP

75034

What drives Frisco pricing

Local labor

Rapid growth keeps Frisco crews booked and prices slightly above metro average.

Permits & code

City permits and HOA review both apply to exterior work.

Climate & conditions

Hail and wind exposure similar to the rest of DFW.

Instant cost calculator

Adjust the inputs to see live pricing

Number of pumps1 unit

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$950 – $1,330

Most homeowners pay around $1,140

Compare quality / material level

Cost by material in Frisco

Installed Frisco pricing per unit.

Option	Installed cost	Pros	Cons
1/3 HP pedestal	$1,000 – $1,400	—	—
1/2 HP submersible	$1,400 – $1,850	—	—
Submersible with battery backup	$1,850 – $2,400	—	—
Dual pump with water-powered backup	$2,400 – $3,300	—	—

Where the money goes in Frisco

A typical $1,650 Frisco project, broken down by line item.

Labor0.45% · $7
Materials0.38% · $6
Permits & inspections0.05% · $1
Overhead & profit0.12% · $2

Common add-ons

Extras that show up on Frisco quotes but rarely in the headline price.

Battery backup system

$425 – $1,250

New sump pit excavation

$530 – $1,900

Discharge line extension

$160 – $635

Interior drain tile

$3,200 – $10,600

Ways to save in Frisco

Install backup power — most failures happen during storm outages.
Replace preventively at year 8 instead of after a flood.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Frisco FAQs

Get a Frisco price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your TX ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Frisco research

Best sump pump installation companies in Frisco Sump Pump Installation permits in Texas Sump Pump Installation near me All Texas prices

Sump Pump Installation cost near Frisco

Sump Pump Installation cost in Dallas, TX

$611 – $2,550

Sump Pump Installation cost in Fort Worth, TX

$599 – $2,500

Sump Pump Installation cost in Plano, TX

$629 – $2,625

Sump Pump Installation cost in Arlington, TX

$593 – $2,475

Sump Pump Installation cost in Irving, TX

$599 – $2,500

Sump Pump Installation cost in McKinney, TX

$623 – $2,600

More Texas cities

Denton Garland Houston Katy Sugar Land The Woodlands Pearland Pasadena

Other project costs in Frisco

Fence Installation in Frisco

$1,590 – $4,240

Roof Replacement in Frisco

$9,010 – $36,040

Kitchen Remodel in Frisco

$19,080 – $100,700

HVAC Replacement in Frisco

$5,830 – $19,080

Deck Building in Frisco

$4,664 – $12,720

Window Replacement in Frisco

$477 – $1,590

See every Frisco cost guide