How much does sump pump installation cost in Irving, TX?

Most Irving homeowners spend between $600 – $2,500 on sump pump installation, with an average around $1,550. Local labor prices right at the national average, so Irving quotes tend to land at the higher end of national ranges.

Why is sump pump installation more or less expensive in Irving than elsewhere?

Irving quotes track the DFW average closely. Hail and wind events drive periodic roof replacement.

Do I need a permit for sump pump installation in Irving, Texas?

City permits apply to most exterior and mechanical work. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Irving?

Get at least three written quotes from licensed, insured Texas contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Dallas-Fort Worth market.

How much does sump pump installation cost in 2026?

Most homeowners pay between $600 and $2,500, with a national average near $1,550. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per unit?

Installed pricing usually runs $600.00 to $2,500.00 per unit, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-unit price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Sump Pump Installation/Irving, TX

Dallas-Fort Worth · Texas

Sump Pump Installation cost in Irving, TX

Irving homeowners typically pay $600 – $2,500 for sump pump installation. Local labor and materials price right at the national average.

Get my Irving estimate Use the Irving calculator

Irving average

$1,550

Typical low

$600

Typical high

$2,500

Per unit

$600 – $2,500

Sample ZIP

75038

What drives Irving pricing

Local labor

Irving quotes track the DFW average closely.

Permits & code

City permits apply to most exterior and mechanical work.

Climate & conditions

Hail and wind events drive periodic roof replacement.

Instant cost calculator

Adjust the inputs to see live pricing

Number of pumps1 unit

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$912 – $1,235

Most homeowners pay around $1,074

Compare quality / material level

Cost by material in Irving

Installed Irving pricing per unit.

Option	Installed cost	Pros	Cons
1/3 HP pedestal	$960 – $1,300	—	—
1/2 HP submersible	$1,300 – $1,750	—	—
Submersible with battery backup	$1,750 – $2,250	—	—
Dual pump with water-powered backup	$2,250 – $3,100	—	—

Where the money goes in Irving

A typical $1,550 Irving project, broken down by line item.

Labor0.45% · $7
Materials0.38% · $6
Permits & inspections0.05% · $1
Overhead & profit0.12% · $2

Common add-ons

Extras that show up on Irving quotes but rarely in the headline price.

Battery backup system

$400 – $1,200

New sump pit excavation

$500 – $1,800

Discharge line extension

$150 – $600

Interior drain tile

$3,000 – $10,000

Ways to save in Irving

Install backup power — most failures happen during storm outages.
Replace preventively at year 8 instead of after a flood.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Irving FAQs

Get a Irving price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your TX ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Irving research

Best sump pump installation companies in Irving Sump Pump Installation permits in Texas Sump Pump Installation near me All Texas prices

Sump Pump Installation cost near Irving

Sump Pump Installation cost in Dallas, TX

$612 – $2,550

Sump Pump Installation cost in Fort Worth, TX

$600 – $2,500

Sump Pump Installation cost in Plano, TX

$630 – $2,625

Sump Pump Installation cost in Frisco, TX

$636 – $2,650

Sump Pump Installation cost in Arlington, TX

$594 – $2,475

Sump Pump Installation cost in McKinney, TX

$624 – $2,600

More Texas cities

Denton Garland Houston Katy Sugar Land The Woodlands Pearland Pasadena

Other project costs in Irving

Fence Installation in Irving

$1,500 – $4,000

Roof Replacement in Irving

$8,500 – $34,000

Kitchen Remodel in Irving

$18,000 – $95,000

HVAC Replacement in Irving

$5,500 – $18,000

Deck Building in Irving

$4,400 – $12,000

Window Replacement in Irving

$450 – $1,500

See every Irving cost guide