How much does cabinet refacing cost in Frisco, TX?

Most Frisco homeowners spend between $2,650 – $9,350 on cabinet refacing, with an average around $6,000. Local labor prices 6% above the national average, so Frisco quotes tend to land at the higher end of national ranges.

Why is cabinet refacing more or less expensive in Frisco than elsewhere?

Rapid growth keeps Frisco crews booked and prices slightly above metro average. Hail and wind exposure similar to the rest of DFW.

Do I need a permit for cabinet refacing in Frisco, Texas?

City permits and HOA review both apply to exterior work. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Frisco?

Get at least three written quotes from licensed, insured Texas contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Dallas-Fort Worth market.

How much does cabinet refacing cost in 2026?

Most homeowners pay between $2,500 and $8,800, with a national average near $5,650. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per linear foot?

Installed pricing usually runs $100.00 to $350.00 per linear foot, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-linear foot price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Cabinet Refacing/Frisco, TX

Dallas-Fort Worth · Texas

Cabinet Refacing cost in Frisco, TX

Frisco homeowners typically pay $2,650 – $9,350 for cabinet refacing. Local labor and materials price 6% above the national average.

Get my Frisco estimate Use the Frisco calculator

Frisco average

$6,000

Typical low

$2,650

Typical high

$9,350

Per linear foot

$105 – $370

Sample ZIP

75034

What drives Frisco pricing

Local labor

Rapid growth keeps Frisco crews booked and prices slightly above metro average.

Permits & code

City permits and HOA review both apply to exterior work.

Climate & conditions

Hail and wind exposure similar to the rest of DFW.

Instant cost calculator

Adjust the inputs to see live pricing

Cabinet run (linear feet)25 linear feet

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$3,563 – $4,869

Most homeowners pay around $4,216

Compare quality / material level

Cost by material in Frisco

Installed Frisco pricing per linear foot.

Option	Installed cost	Pros	Cons
Rigid thermofoil	$150 – $205	—	—
Wood veneer	$205 – $265	—	—
Solid wood doors	$265 – $345	—	—
Custom paint-grade solid wood	$345 – $475	—	—

Where the money goes in Frisco

A typical $6,000 Frisco project, broken down by line item.

Labor0.45% · $27
Materials0.38% · $23
Permits & inspections0.05% · $3
Overhead & profit0.12% · $7

Common add-ons

Extras that show up on Frisco quotes but rarely in the headline price.

New hardware

$105 – $635

Soft-close hinges and slides

$210 – $955

Pull-out shelving

$160 – $530

Crown molding

$320 – $1,250

Ways to save in Frisco

Reface only the uppers and paint the lowers for a two-tone look.
Reuse existing hardware if the hole spacing matches.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Frisco FAQs

Get a Frisco price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your TX ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Frisco research

Best cabinet refacing companies in Frisco Cabinet Refacing permits in Texas Cabinet Refacing near me All Texas prices

Cabinet Refacing cost near Frisco

Cabinet Refacing cost in Dallas, TX

$2,550 – $8,997

Cabinet Refacing cost in Fort Worth, TX

$2,500 – $8,821

Cabinet Refacing cost in Plano, TX

$2,625 – $9,262

Cabinet Refacing cost in Arlington, TX

$2,475 – $8,733

Cabinet Refacing cost in Irving, TX

$2,500 – $8,821

Cabinet Refacing cost in McKinney, TX

$2,600 – $9,174

More Texas cities

Denton Garland Houston Katy Sugar Land The Woodlands Pearland Pasadena

Other project costs in Frisco

Fence Installation in Frisco

$1,590 – $4,240

Roof Replacement in Frisco

$9,010 – $36,040

Kitchen Remodel in Frisco

$19,080 – $100,700

HVAC Replacement in Frisco

$5,830 – $19,080

Deck Building in Frisco

$4,664 – $12,720

Window Replacement in Frisco

$477 – $1,590

See every Frisco cost guide