How much does cabinet refacing cost in Irving, TX?

Most Irving homeowners spend between $2,500 – $8,800 on cabinet refacing, with an average around $5,650. Local labor prices right at the national average, so Irving quotes tend to land at the higher end of national ranges.

Why is cabinet refacing more or less expensive in Irving than elsewhere?

Irving quotes track the DFW average closely. Hail and wind events drive periodic roof replacement.

Do I need a permit for cabinet refacing in Irving, Texas?

City permits apply to most exterior and mechanical work. Always confirm current requirements with the local building department before signing a contract, and make sure the permit is pulled by your licensed contractor.

How many quotes should I get in Irving?

Get at least three written quotes from licensed, insured Texas contractors. Comparing line items — not just the bottom line — is the fastest way to spot an inflated bid in the Dallas-Fort Worth market.

How much does cabinet refacing cost in 2026?

Most homeowners pay between $2,500 and $8,800, with a national average near $5,650. Small, simple jobs land at the low end; large or premium-material jobs run well above the high end.

What is the cost per linear foot?

Installed pricing usually runs $100.00 to $350.00 per linear foot, including labor and materials. Expensive metros can run 15–45% higher than that range.

What drives the price up the most?

Scope and access. Larger quantities lower your per-linear foot price, but difficult access, demolition of existing work, structural repairs found mid-job, premium materials and rush scheduling each add 8–30%.

Permits are typically required when the work changes structure or ties into electrical, plumbing, gas or mechanical systems. Budget $75–$600 in most cities and confirm whether your contractor pulls it — unpermitted work can block a future home sale.

How long does the job take?

Most residential projects of this type finish in one to five working days once materials are on site. Custom orders, inspections and weather are the usual causes of delay.

How many quotes should I get?

Three. Bids on the same scope commonly vary 20–40%, and the middle bid with the strongest warranty and references is usually the best value — the cheapest bid often excludes prep, disposal or permits.

Home/Cost guides/Cabinet Refacing/Irving, TX

Dallas-Fort Worth · Texas

Cabinet Refacing cost in Irving, TX

Irving homeowners typically pay $2,500 – $8,800 for cabinet refacing. Local labor and materials price right at the national average.

Get my Irving estimate Use the Irving calculator

Irving average

$5,650

Typical low

$2,500

Typical high

$8,800

Per linear foot

$100 – $350

Sample ZIP

75038

What drives Irving pricing

Local labor

Irving quotes track the DFW average closely.

Permits & code

City permits apply to most exterior and mechanical work.

Climate & conditions

Hail and wind events drive periodic roof replacement.

Instant cost calculator

Adjust the inputs to see live pricing

Cabinet run (linear feet)25 linear feet

Quality / material level

Site access

Removal / prep work

Timing

Estimated project cost

$3,325 – $4,513

Most homeowners pay around $3,919

Compare quality / material level

Cost by material in Irving

Installed Irving pricing per linear foot.

Option	Installed cost	Pros	Cons
Rigid thermofoil	$140 – $190	—	—
Wood veneer	$190 – $250	—	—
Solid wood doors	$250 – $325	—	—
Custom paint-grade solid wood	$325 – $450	—	—

Where the money goes in Irving

A typical $5,650 Irving project, broken down by line item.

Labor0.45% · $25
Materials0.38% · $21
Permits & inspections0.05% · $3
Overhead & profit0.12% · $7

Common add-ons

Extras that show up on Irving quotes but rarely in the headline price.

New hardware

$100 – $600

Soft-close hinges and slides

$200 – $900

Pull-out shelving

$150 – $500

Crown molding

$300 – $1,200

Ways to save in Irving

Reface only the uppers and paint the lowers for a two-tone look.
Reuse existing hardware if the hole spacing matches.
Collect three written bids on an identical scope — spreads of 20–40% are normal.
Book in the off-season and stay flexible on the start date to save 5–15%.
Bundle nearby work into one mobilization so you only pay setup and travel once.
Ask what the contractor would change to cut 10% without hurting durability.

Irving FAQs

Get a Irving price you can budget against

Answer a few questions about your project and we'll model a low, average and premium price for your TX ZIP code — then connect you with vetted local pros.

Get free quotes from certified pros

More Irving research

Best cabinet refacing companies in Irving Cabinet Refacing permits in Texas Cabinet Refacing near me All Texas prices

Cabinet Refacing cost near Irving

Cabinet Refacing cost in Dallas, TX

$2,550 – $8,976

Cabinet Refacing cost in Fort Worth, TX

$2,500 – $8,800

Cabinet Refacing cost in Plano, TX

$2,625 – $9,240

Cabinet Refacing cost in Frisco, TX

$2,650 – $9,328

Cabinet Refacing cost in Arlington, TX

$2,475 – $8,712

Cabinet Refacing cost in McKinney, TX

$2,600 – $9,152

More Texas cities

Denton Garland Houston Katy Sugar Land The Woodlands Pearland Pasadena

Other project costs in Irving

Fence Installation in Irving

$1,500 – $4,000

Roof Replacement in Irving

$8,500 – $34,000

Kitchen Remodel in Irving

$18,000 – $95,000

HVAC Replacement in Irving

$5,500 – $18,000

Deck Building in Irving

$4,400 – $12,000

Window Replacement in Irving

$450 – $1,500

See every Irving cost guide